Silverstone Raven: A New Concept in Case Cooling
by Christoph Katzer on February 6, 2009 4:00 AM EST- Posted in
- Cases/Cooling/PSUs
Inside
The case design concept is indeed very different, and even if the cooling isn't any better there are almost certainly people that would still approve of this case design. However, we think that the cooling design is effective, since heat should exhaust easier through the top of the chassis. You can also get fresh air for some important components without having to draw air through the entire chassis; for example, a power supply with a 120mm fan on the bottom gets direct access to fresh air. Higher end GPUs should also get access to a lot of fresh air from the side panel vents. A 120mm fan serves as the primary exhaust at the top of the case, and Silverstone again uses positive air pressure with more intake fans than exhaust fans in order to optimize cooling.
Towards the front of the case are six hard drive cages that can be removed by opening the appropriate lever and sliding them out. This allows you to easily install hard drives, and small rubber grommets isolate the hard drives and keep them from touching the rest of the chassis. This should reduce vibrations and thus decrease noise levels. The drive bay on the left includes a back plate that enables hot swapping of that hard drive. Optical drives use the same mounting system Silverstone has used in other cases.
One of the interesting benefits of the case design is that you shouldn't have to worry as much about graphics cards causing flex on your motherboard. They can now hang from the top of the case and shouldn't sag. In addition, you can use a support bar that reaches across the motherboard to help secure the graphics cards. The bottom of the case has a ton of space, so you can easily install even the longest of power supplies. The air filters at the bottom are easily removed for cleaning, although you will need to remove the side panel for some of the filters. Finally, there's a bit of extra room behind the motherboard where you can route some smaller cables if you desire, but it's not a particularly large area so you won't be able to route all of the cable harnesses that way.
Facebook
Twitter
RSS
49 Comments
View All Comments
Sabresiberian - Tuesday, March 31, 2009 - link
Personally, I've bought my last pre-made case; the only exception is the Skeleton, I might buy one of those just to support Antec's thinking 'out of the box' (literally and figuratively), though it doesn't quite live up to an enthusiast's case. Better than any other design, though.Really, even the so-called high air flow cases as they come from the manufacturers are inadequate; the best I can say about them, and this goes for this case in particular, is that they do control noise a bit better as well as giving some slight air flow benefits. The thinking of air flow needs to change though, from power supplies, which have fans good enough to cool themselves and don't add much heat to the system except that they BLOCK air movement, to actually removing hot air from a system, rather than just stirring it up, for the entire industry. Imo.
My last case purchase was a Silverstone; it was purchased when the industry was talking BTX, which never happened, and was touted for it's cooling capabilities. I think of it as a good case, it is mostly well-made, but as I think back it came with a very cheap air shroud that couldn't even be used in a stock system, and tabs broke off when I tried to use it. I'm not a fan of clip-in expansion slots either, especially with modern video cards weighing as much as they do. Give me screws any time.
The best feature of the Raven imo is that the video cards will hang straight down and put less side-ways stress on the expansion slots - assuming they are securely held by the case, that is.
Anyway, I want a system that is easy to mess with as well as supporting maximum cooling, whether that means good air flow or liquid cooling or both. Hard core overclockers don't even use cases - and while I'm not currently in that class, I do make changes and still had to leave the side cover off my Silverstone case with a fan blowing in to keep my non-overclocked video card happy (I've changed cards and this is no longer necessary, but it never should have been; partly a fault of ATI (and Nvidia in another rig) and partly Silverstone and the way almost all cases are made.)
If noise is a big factor, or you need portability, or love the cool looks of some of the new case, or just the convenience of having a pre-made, I can't argue with any of those things. For me though, they are all inadequate, and I'd just as soon not support an industry, if I can help it, that continues to go down the wrong path. My newest build uses a heavily modified old Antec, but I can OC my i7 to 4.1GHz on air (Cooler Master V8) stress-tested for stability, something which almost all current cases would hamper if not make impossible.
Kudos to Silverstone for doing some original thinking though; I had some extraordinary difficulties with them regarding a power supply (I did end up with a good power supply, just took too much time and effort to get imo) so am not likely to send any more of my business their way, but they do have some fresh ideas and do produce pretty cases.
Sladeofdark - Friday, February 20, 2009 - link
cases like this make me want to get a job working for the companies that make some of this terrible cases.. what a waste of metal. It looks cool and would look even cooler if the tacky , cheaply implemented window were taken out. Some of the cosmetic standards that have been set need not be undermined by new projects. the mobo orientation is a disaster, i dont see a point to it at all. the stiffness and weight of the DVI cord to a monitor will cause "bowing" and sever the on board video at the connection point of the port to the mobo meaning it cant be repaired. ive seen this happen when people push their towers up against a wall while under their desk. in this case gravity will be the wall, where will all the wires go i have ( looks under his desk) about 10 cords connected to my mobo. what will that look like coming out of the top of the case except awful. this was a miss hit to say the least.vistaisfine - Friday, February 20, 2009 - link
the intakes on the bottom work well. people who complain about cleaning the filters need to either A) vacuum the floor more B) get it out of the garage / basement (concrete dust). C) remember to clean the filters regularly. this coming from a cosmos 1010 user.JeBarr - Wednesday, February 11, 2009 - link
Anybody try squeezing a 4th GPU in there yet? I'm too broke these days to find out, though the price on this chassis is much lower than I had anticipated originally. I don't need to here how bad of an idea that is, or how incapable the chassis is it at removing the heat in that scenario...I just want to know, will they fit?bkusnerik - Tuesday, February 10, 2009 - link
Wow... something new like this motherboard orientation and no pictures of how it looks with the cables connected? Come on!7Enigma - Tuesday, February 10, 2009 - link
Is clearly the very poor and small top fan for exhaust. The problem I see here is positive pressure is great as long as it's SLIGHTLY more. This looks like it would be building up quite a bit of heat at the top, possibly even forcing hot air back down to exit out of the side holes which I'm guessing do practially nothing (look at the picture showing 3! separate shrouds between the inside and the outside of the case) due to the restrictions.Aesthetically I don't care. I'm utilitarian by nature when it comes to a case but it looks unique. I think the only way this would be practical would be to ensure that you DEFINITELY had a GPU that externally exhuasted the air out the top. Most of the coolers on cards today either outright exhaust into the case (this would be really bad for this particular one), or only partially exhaust out the back (or top in this case). I think if you had a good exhausting GPU cooler it could alleviate some of the issues with the large bias towards positive pressure.
jabber - Sunday, February 8, 2009 - link
Yes I'd like to see some pics of it fully cabled too.I dont see how a nice chunky DVI cable with a ferrite core on it will manage, plus I have to use the VGA socket on the monitor at home (I game, the Gf does design so she gets the DVI)so also have to factor a DVI to VGA adapter too. Thats about 4 inches+ of stress right there.
Cmon lets see some real in sction pics.
SLayVus - Sunday, February 8, 2009 - link
Here are some picturesCamera: FujiFilm FinePix S1000fd - Component side
http://i205.photobucket.com/albums/bb94/killer_che...">http://i205.photobucket.com/albums/bb94/killer_che...
Camera: Sanyo VPC-T700 - Cable management
http://i205.photobucket.com/albums/bb94/killer_che...">http://i205.photobucket.com/albums/bb94/killer_che...
Camera: FujiFilm FinePix S1000fd - Desk
http://i205.photobucket.com/albums/bb94/killer_che...">http://i205.photobucket.com/albums/bb94/killer_che...
i7 920@ 3.8GHz 25*C(Core @ 38*C Idle) - ThermalRight Limited Edition Black TRUE - G.Skill PI Black DDR3-1600 3x2GB - MSI X58 Platinum Non-Sli - VisionTek HD 4870 X2 - 3x500GB WD Caviar Black 32MB 7.2k w/CP05 hotswap adapters - Antec 850w(Corsair 1000HX on the way)
kmmatney - Sunday, February 8, 2009 - link
Your cable management pic is just like my Antec P180 case - I spent hours getting all the cables routed around the back of the motherboard. It was great for about 6 months, and then I needed to take my power supply out to test on another computer (helping out a friend). After that, it just wasn't worth all the time and effort - I just keep the cables routed around the front. Not as clean, but much easier to remove the power supply if necessary.jrcaptain - Saturday, February 7, 2009 - link
You'll also need to remove the top panel anytime you want to access the side panels, since the two lovers that open the sidesthe two lovers.....levers