Silverstone Raven: A New Concept in Case Cooling
by Christoph Katzer on February 6, 2009 4:00 AM EST- Posted in
- Cases/Cooling/PSUs
Inside
The case design concept is indeed very different, and even if the cooling isn't any better there are almost certainly people that would still approve of this case design. However, we think that the cooling design is effective, since heat should exhaust easier through the top of the chassis. You can also get fresh air for some important components without having to draw air through the entire chassis; for example, a power supply with a 120mm fan on the bottom gets direct access to fresh air. Higher end GPUs should also get access to a lot of fresh air from the side panel vents. A 120mm fan serves as the primary exhaust at the top of the case, and Silverstone again uses positive air pressure with more intake fans than exhaust fans in order to optimize cooling.
Towards the front of the case are six hard drive cages that can be removed by opening the appropriate lever and sliding them out. This allows you to easily install hard drives, and small rubber grommets isolate the hard drives and keep them from touching the rest of the chassis. This should reduce vibrations and thus decrease noise levels. The drive bay on the left includes a back plate that enables hot swapping of that hard drive. Optical drives use the same mounting system Silverstone has used in other cases.
One of the interesting benefits of the case design is that you shouldn't have to worry as much about graphics cards causing flex on your motherboard. They can now hang from the top of the case and shouldn't sag. In addition, you can use a support bar that reaches across the motherboard to help secure the graphics cards. The bottom of the case has a ton of space, so you can easily install even the longest of power supplies. The air filters at the bottom are easily removed for cleaning, although you will need to remove the side panel for some of the filters. Finally, there's a bit of extra room behind the motherboard where you can route some smaller cables if you desire, but it's not a particularly large area so you won't be able to route all of the cable harnesses that way.
Facebook
Twitter
RSS
49 Comments
View All Comments
Visual - Friday, February 6, 2009 - link
i really don't fancy the idea of intake fans on the bottom. there's going to be a huge amount of dust gathering down there.and expansion cards and cables at the top, really? maybe it can work if i hide the case under the desk, but what if it is on top?
weevil - Friday, February 6, 2009 - link
But you would never have to sweep the floor.HelToupee - Friday, February 6, 2009 - link
I really like the idea of the layout of this case. It's the perfect arrangement for an under-the-desk setup. You are right that the intakes on the bottom of the case are a terrible idea. They'll clog with dust, and need cleaning constantly, and are in the most inconvenient place they could possibly be. Maybe if they add some kind of ducting along the back to direct air underneath the case and raised the case off the ground a bit.What I really like is the cable management. Where the cables come out of the power supply is right next to where they plug into the motherboard. If you look at the pictures of the system assembly, there are no cables at all routed over the motherboard. All the cable mess tucks nicely away into the bottom front of the case where it's not visible, and not in the way of airflow. Perfect. Plus, when the case is sitting under your desk, all the ports are the closest they can be to where you want them -- rear top of the case. I love the idea of having access to the back panel (now on top) of the case by just rolling the case out a bit. Lighting will be better, cables will not be strained and crimped around corners. Very convenient.
I hope other (cheaper) options appear with this configuration. I may have to consider picking one up.
Dreamwalker - Friday, February 6, 2009 - link
A very interesting case, but I do wonder how you manages the cables that are coming at the top, the VGA cables and all the other stuff. A picture would be great here. Can't realy imagine how it looks like all the cables coming at the top rather than from the bac side.Anyone got the Lamborghini Reventon in his minde when looking at he pictures?
weevil - Friday, February 6, 2009 - link
Looks like an F-117 Stealth fighter to me, Love the interier but the outside is ugly. But at least it will evade radar, I could replace the fairing on my Harley with this and the CHP will never see me.strikeback03 - Friday, February 6, 2009 - link
Personally, I think the person in the previous look who compared it to a Jawa Sandcrawler was dead-on.Bigjee - Friday, February 6, 2009 - link
That's the first thing that came to my mind.The lamborghini Reventon.
This case perfectly portrays it. The lines make it look like its been designed by the same person who designed that car.
soydeedo - Friday, February 6, 2009 - link
With dreadlocks.maxnix - Thursday, April 28, 2011 - link
Had this case two years now and it has been rock solid except for a bad fan that would rattle when installed. Replaced with an even quieter one and all is well. Not overclocked yet, so acoustic signature could increase when it is. Access is great and easy. Case is heavy.Now the Raven 3 is out.
By the way the filters while rudimentary, are a lot better than nothing in most other cases.